Thermal Shock Test

Temperature Cycling Test Systems

Thermal Cycling Test Systems

Thermal Test Systems

Temperature Test Chambers

Temperature Test Semiconductor Components

Temperature Cycling Chamber

Temperature Inducing Systems

Thermal Inducing Chambers

Temperature Cycling Test Chambers

Temperature Inducing Chamber 

Temperature Test Chamber

Advanced Technology

Environmental temperature test chambers can just go so far when it comes to precise thermal control, fast ramp rates, and narrow temperature margins in some product test procedures and processes. Instead of taking your parts to a large test chamber, ThermalAir Systems bring the temperature to your components at your test location.

 

MPI ThermalAir temperature forcing systems provide a direct thermal stream of clean dry hot and cold air directly to the part that needs to be thermal tested. Environmental stress screening, temperature conditioning, thermal shock and other temperature test requirements is what the ThermalAir temperature systems bring to the test.

Environmental Test Chamber

Temperature Forcing Systems | Environmental Stress Test | Environmental Test Chambers | Temperature Test Systems | Temperature Test | Temperature Test Equipment | Temperature Test Systems

Anechoic Environmental Test Chamber Measure Super Quiet Chiller at 45 dBA

Our Patented Noise Reduction Technology has been tested in a environmental anechoic test chamber. The TA-5000 ThermalAir temperature system running at full capacity measures 45 dBA. This is 100 times less noise energy than the closest competitors temperature forcing air stream system.

This new DC ThermalAir Technology lets you “Plug in Anywhere!” One system fits all countries for worldwide compatible for 50Hz or 60Hz power. The MPI ThermalAir temperature system can be used in any region of the world [no configuration required]. It does not need rewire of system for 50Hz / 60Hz. The DC chiller and DC Heater patented technology runs at full temperature performance at any power frequency, 200VAC to 250VAC users facility.

ThermalAir Stream Temperature Testing Sytems w/ GUI Simulation

Rapid Thermal Cycling Test Solutions

The illustration (Left) shows the common use of the ThermalAir stream temperature forcing systems.

MPI Thermal systems bring your test articles to hot and cold temperatures in many different ways for your thermal test applications. Whether the test engineers requires inducing temperature on a single semiconductor device, an electronic module or PCB, or a mechanical device, MPI ThermalAir systems can bring temperature to the test instead of having to take the part to a large environmental test chamber.

The video shows the GUI (Graphic User Interface) running as you see the simple operation of the ThermalAir TA-5000 model below used in a variety of different setups for an array of test application providing hot and cold forced air without the need for LN2 or CO2 gases. 

  • DC Chiller Control System

  • DC Heater Control Function

  • Thermal Cap & Flex Hose Lock Interface

  • Exhaust Frost Protection

  • Reduced Noise Air Dryer

  • Defrost Chiller Function

  • Thermal Cap Connection Head

  • IR Sensor for Heater Protection & Safety

Temperature Cycling Test | Rapid Thermal Cycling Solutions | Temperature Test Solutions | Semiconductor Temperature Testing

Performance Plus!

The ThermalAir Temperature Forcing System is Environmental Friendly!

Its time to “GO GREEN”!

MPI Thermal TA-5000 temperature test system has 50% energy saving compared to similar temperature test chamber systems.

This Green machine does it without giving up temperature performance. Our new patented technology is designed to be Eco Friendly.

Temperature Test Solutions | Thermal Test Solutions | Semiconductor Temperature Testing | Temperature Cycling Test | Thermal Test Equipment | Rapid Thermal Cycling Solutions

Field Application Engineer

Job Location: San Jose, CA

Job Duties:

  • Assist in developing HW and SW measurement methodologies/solutions for analytical wafer probe solutions with signal applications from DC to millimeter wave frequencies as well as Silicon Photonics (SiPH);
  • Collaborate with customers on their measurement challenges, and provide applications specific product training;
  • Provide pre- and post-sale support to AST, customers, service department, and the sales channel developing HW and SW measurement solutions for analytical wafer probe stations;
  • Define application-specific solutions based on customer-provided device data and facilitate both customer and divisional teams to successful results;
  • Perform product training seminars for customer and sales channels as well as participate in trade shows and technical seminars;
  • Make recommendations regarding product improvement, new products, and quality enhancement;
  • Author, document, publish, and present measurement solutions via Seminars, Applications Notes, Briefs, and White Papers;
  • Prepare, plan, and assist with customer product demonstrations that highlight value-based differentiation of AST product offerings;
  • Develop unique and individual customer presentations designed to professionally position the MPI brand in the North American market and deliver formal presentations to customers.

Job Requirements:

Master’s degree in Electrical Eng., Electronics Eng., Physics, or Photonics; Must possess 6 months of relevant work experience; Travel to customers’ sites in US and headquarters in Taiwan is required.

Send resume to: MPI America, Inc., 2360 Qume Drive, Suite C, San Jose, CA 95131, Attn: Janet Chiang